![]() ![]() Sophos offer technical documentation for XG at Getting Startedįirst you need to log in to the Web Console portal from your client device connected to the LAN interface of the Sophos XG server. We've thoroughly tested the steps in this guide to ensure that, if you follow the instructions detailed below, you should be well on your way to enjoying the benefits of running your own OpenVPN server. We provide this guide as a courtesy to help you get started with, and make the most of, your copy of Viscosity. Unfortunately we cannot provide any direct support for setting up your own OpenVPN server. If you don't have a copy of Viscosity already installed on your client machine, then please check out this setup guide for installing Viscosity ( Mac | Windows). The specifics of how you can achieve this depend on your particular network configuration. This is necessary so that you can access the Web Console portal to set up the Sophos XG configuration. Your client device needs to be connected to the Sophos XG server via the LAN interface. ![]() If you are looking to setup an OpenVPN server on a different operating system, please check out our other guides. If you are running a different version of Sophos XG, it's very likely that many or even all of the steps outlined in this guide will still apply. We won't be covering the details of setting up a Sophos XG instance. If you need to download and install a copy of Sophos XG, information can be found at. You already have a copy of Viscosity installed on your client device.This installation of Sophos XG is a fresh install.Sophos XG is using the default LAN subnet 172.16.16.0/24.You are connected with your client device to the Sophos XG server via its LAN interface during this guide.Sophos XG has been set up with at least a WAN interface and a LAN interface.You have already installed the latest version of Sophos XG (18.0.5 at time of writing).If you want to support me, buy stuff over my Amazon links or click on an advertisement.This guide will walk you through the steps involved in setting up an OpenVPN server on a Sophos XG host that allows you to securely access your home/office network from a remote location and optionally send all of your network traffic through it so you can access the internet securely as well.īefore using this guide, we highly recommend you read through our Introduction to Running an OpenVPN Server Article. Registration, Software Download and Installation Sophos UTMįeel free to comment the recommendation or ask for further installation help. These are my server components: CPUĢx be Quiet Pure Wings 2 (case back and for the hdd’s) If you need inspiration for a home server. You can use it for guest wifi or whatever you want. You can use vlan interfaces for eth0 without any setup by the hypervisor. On my UTM for LAN eth0 (virtio) and for WAN eth1(PCI Passtrough realtec NIC).Ī nice feature. If it was the wrong interface, restart the installation process and select the other NIC in the list for the LAN.Īfter the installation, you have 2 hardware NICs in the UTM. The LAN-NIC should be the first interface. When installing the UTM, you must select a LAN NIC. insert the “WAN NIC” via PCI Passthroughīe sure if it is the right PCIe slot and NIC.I recommend virtio for NIC device model, because according to my own experience it offers the best data throughput. activate the bridge mode for the “LAN NIC”.activate auto start while booting of the hypervisor.We have been busy and now have a fully installed Ubuntu and Virt Manager and are starting to configure the virtual UTM. With PCI Passthrough, all traffic goes directly to the virtual firewall and cannot escape from a virtual switch and has no logical contact with the hypervisor (the Ubuntu server). Why do I use PCI Passthrough? It is safer. you need a pcie slot for the NIC where the PCIe lanes are not shared with the chipset or other components.and the last NIC via PCI Passthrough exclusive for the UTM WAN interface (you can’t use a dual NIC for this).the second NIC in bridge mode for the VMs.I use the Mainboard NIC for the Server management. ![]() A Ubuntu System (with a GUI, it’s easier ) ).The following link deals with the basic configuration of virt manager under ubuntu: In this article I assume that Ubuntu and virt manager are installed. Today I will tell you how I configured my home server for a virtual Sophos UTM.Īll configurations in ubuntu can also be used for a virtual Sophos XG. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |